Cross-reference iRING/IIP TIPs vs new TIPs

latest update: 2017-01-06    

Introduction

The iRING TIPs (see overview)  that can be found in the TIP Manager (takes some time to start up) are descriptive.

This page is giving, for each iRING TIP, a cross-reference to the new TIPs that are mapped to ISO 15926-7/8 exchange files.

NOTE 1 - The new TIP IDs were necessary because several iRING TIPs could be mapped to one generic solution with one or more picklists with Reference Data Library classes.

NOTE 2 - In case "RDS" is shown, the RDL is the source, in case "R" is shown, some local RDL extension may be implied in cases where the example given in the TIP Manager is company- or project-specific.

iRING  TIP ID

TIP Name

TIP Description

Typical value

Remark

new TIP ID (NOTE 1)

Use RDL class (NOTE 2)

T0001

Tag

A unique functional identification code for an object within a context such as a plant

HX-1234

"Tag" has several specializations

TIP0001

RDS2221089

T0002

Actuator Type

Mechanism to modulate a control device such as a valve in response to a signal or power input

Hand Wheel, Motor, Hydraulic etc.

 

TIP1200

 

T0003

Air Connection Required

Whether air supply is required or not

Y, N

 

TIP3100

 

T0004

Alarm Limit H

Alarm limit high

200,40, C m

Without process variable these are meaningless. Use for Analysis, Flow, Level, Pressure, Temparature respectively:

TIP3400 TIP3600 TIP4200 TIP4400 TIP5000

 

T0005

Alarm Limit HH

Alarm limit high high

240,50, C,m

 

T0006

Alarm Limit L

Alarm limit low

20,5, C,m

 

T0007

Alarm Limit LL

Alarm limit low low

10,4, C,m

 

T0008

Atmospheric Pressure

A pressure that is representing the weight of the air column standing vertically over the place where the measurement is done

998,29, mbar, inches Hg

Declare an instance of SpatialLocation that covers the area where the Atmospheric Pressure is measured.

TIP6600

 

T0009

Beta Ratio

The ratio of the diameter of the orifice bore to the pipe diameter

0.5

 

 

 

T0010

Cable Gland Type

The type of support for a cable where the cable is to be terminated

Acme Gland Co M50, Acme Gland Co M50

the 'whole' being the junction box or the like

TIP1200

 

T0011

Calibrated Range Lower Limit

Lower known process value given to instrument for its calibration.

0,0, C, m

Without process variable these are meaningless. Use for Analysis, Flow, Level, Pressure, Temparature respectively:

TIP3400 TIP3600 TIP4200 TIP4400 TIP5000

 

T0012

Calibrated Range Upper Limit

Upper known process value given to instrument for its calibration.

400,10, C, m

 

T0013

Calibrated Range

The span of accurate measurement for a certified measuring device

0, 4, barg, Pressure, Temp

 

 

 

T0014

Supplier Catalog Item Number

Identification code that represents an item in a catalog either electronic or physical.

MN 12345

 

 

 

T0015

Certificate Date of Approval for Use

Date/Time a certificate of Approval for Use is issued

12.30:23 Jan 2013

 

 

 

T0016

Certifying Authority

An entity such as an organization responsible for issuing a certificate

NIST, ASME

 

 

 

T0017

Cleaning Requirements  

Cleaning Specification("SmartPlant PID item")

CC1, CC2

 

 

 

T0018

Coating Color

The color name for the coating

RED

 

 

 

T0019

Coating Type

The material type of the coating

PVC, Polyurethane, Epoxy

 

 

 

T0020

Comment

A remark or note of explanation

My favorite pump

 

 

 

T0021

Commodity Group Code

Higher level grouping of artifacts, similar to ISO 15926 Class of Class entity (i.e. GV for Gate Valves)

VALVES, FITTINGS, EQUIPMENTS

 

 

 

T0022

Commodity Name

An alphanumeric code based on the attribution used for definition (ie GV =  Gate Valve, 100 = ID No, BX = Valve Trim Package)

VG100BX

local codes will not end up in RDL

TIP0001

R123456

T0023

Concatenated Instrument Suffix

Concatenation of loop suffix and instrument suffix

AA, AB etc

integrate in full identifier, where required including sheet no. and revision no.

--

--

T0024

Construction Category

Construction status of equipment that determine whether you will buy a new item or reuse an existing item, etc.

New, Existing, Relocated, Demo, Future, Temporary

 

 

 

T0025

Construction Work Package Description

A description for a collection of project objects and associated construction activities

Install pump P-101 and related piping

 

 

 

T0026

Corrosion Allowance

Amount of corrosion permitted before end of service

6, mm

 

 

 

T0027

Data Sheet Description

Text used to describe the artifact on the data sheet

Data Sheet for Main Circulating pump

 

 

 

T0028

Data Sheet Number

Identification number for document summarizing the performance and other technical characteristics of a product

123-HX-001

 

TIP0001

RDS2221088

T0029

Data Sheet Revision

Code to identify and track the revisions for a document

A2, P1, P2, 01, 02, IFC

 

 

 

T0030

Hydro Test Date

Date that a hydrostatic test was carried out

20 July 2013

 

 

 

T0031

Date Installed

Date that installation of artifact was completed

20 July 2013

 

 

 

T0032

Description

A description of the object

Cooling Water Recirc Pump

 

 

 

T0033

Design Area

Logical division of volume within a plant (e.g. process building in a plant, or a group of thickeners)

Thickeners, Building C

 

 

 

T0034

Design Pressure

A pressure based on the normal operating case of the process stream plus a safety factor

225,55, PSI, kPa

 

 

 

T0035

Design Responsibility

The entity responsible for designing an item

Vendor, Contractor, Owner

 

 

 

T0036

Design Sub Area

Logical sub division of volume within a plant

Distillation, 100, A12

 

 

 

T0037

Design Temperature Inline Components

Design temperature for inline piping components

0, C

 

 

 

T0038

Design Temperature Line Segment

Design temperature of the line segment

0, C

 

 

 

T0039

Diameter Internal/Inside

Diameter across an inner cross section of circular object

320, mm

 

 

 

T0040

Differential Head

Change in pressure between two points expressed in liquid height

221, mm Hg

 

 

 

T0041

Differential Pressure

A pressure which is the difference between two pressures; such as the difference between the inlet and outlet of a device

32, kgf/cm^2

 

TIP6600

 

T0042

Discipline Name

Common name of design group responsible for design and/or engineering development

Civil/Electrical/Mechanical/Piping/Structural

 

 

 

T0043

Discipline Code

Short code for design group responsible for design and/or engineering development

P,E,I,S,20,45,6

 

 

 

T0044

Display Label

A label displayed on a drawing for a component that typically consists of the Tag Identification Code concatenated with other properties

V-100, HC-3"-GW0-1234

 

 

 

T0045

Document Category

A classification of document by functional requirement such as piping documents, as-built documents, etc.; which may include documents of more than one type

Isometric Drawing, P&ID, Purchase Order

 

 

 

T0047

Document Revision

Code to identify and track the revisions for a document

A2, P1, P2, 01, 02, IFC

 

 

 

T0048

Document Status

A description of the current state of a document

Review, Revise as Noted, Accepted, Hold for Vendor Info, Superseded

 

 

 

T0050

Document Type

A high-level classification of a document

Technical Document, Drawing

 

 

 

T0051

Document Type Parent Code

Indentification Code for the Source of a piece of written, printed, or electronic matter that provides information or evidence or that serves as an official record, having common characteristics.

040,041

 

 

 

T0052

Driver RPM

Rotational speed of driver

3000, rpm/rps

 

 

 

T0053

Driver Tag Name

Identification Code of Driver

M-0001

 

TIP0001

RDS2221090

T0054

Dry Weight

Estimated or calculated weight of an empty artifact which normally contains a material

2450, kg

 

 

 

T0055

Electrical Power Consumption

Electrical power consumption at normal operating conditions > Measured or calculated design power requirement > Emergency power requirement classification

10, kW

 

 

 

T0056

Emergency Power Required

Emergency power requirement classification

Y/N

 

 

 

T0057

Engineering Work Package Description

A description for a collection of project objects and associated engineering activities

Design fire water system

 

 

 

T0058

Engineering Work Package Number

An identification code for a collection of project objects and associated engineering activities

WP-A035-001

 

TIP0001

RDS2221088

T0059

Enquiry ID

The identifier for a proposal request

E1233449

 

TIP0001

RDS2221088

T0060

Equipment Drawing Number

Alphanumeric code used to identify detailed drawing for equipment

035-M-0001

 

TIP0001

RDS2221088

T0061

Equipment SubType

Detailed classification of equipment

Centrifugal Pump

 

 

 

T0062

Equipment Type

High level classification of equipment

Pump, Rotating Equipment

 

 

 

T0063

Estimated Height

Estimated overall height of an object

1054, mm

 

 

 

T0064

Estimated Length

A approximate linear dimension

10, m

 

 

 

T0065

Estimated Weight

Assumed or calculated weight

2000, lbs

 

 

 

T0066

Estimated Width

An estimated or calculated linear dimension

85, mm

 

 

 

T0067

Fabrication Category

Indication of location of component assembly

Shop,Field

 

 

 

T0068

Facility Description

A description of a commercial or industrial property such as a building, plant, or structure, built, established, or installed for the performance of one or more specific activities or functions

Potable Water supply for the south Chicago area

 

 

 

T0069

Facility Name

A name for a commercial or industrial property such as a building, plant, or structure, built, established, or installed for the performance of one or more specific activities or functions

Water Treatment Facility

 

 

 

T0070

Facility Number

An identification code for a commercial or industrial property such as a building, plant, or structure, built, established, or installed for the performance of one or more specific activities or functions

F-123

 

 

 

T0071

Fail Mode

Status after failure

Open, Closed , Remain in Place

 

 

 

T0072

Failure Action

Activity on failure

Open, Closed

 

 

 

T0073

Field Installed

Whether the instrument/equipment is installed on field or not

Y, N

 

 

 

T0074

Flow Direction

The direction of process flow within a line segment

TypicalValueBidirectional, End 1 is upstream, End 2 is upstream

 

 

 

T0075

Fluid Category

A general classification of a fluid

Acid, Gas, Catalyst

 

 

 

T0076

Fluid Code (Line)

An identification code for a fluid

W, APU

 

 

 

T0077

Functional Area

An area which is a subdivision of a plant by functional areas

An area wThickeners, Building C

 

 

 

T0078

Functional Classification Code

The alphanumeric code to designate a plant item

P, V ect.

 

 

 

T0079

Functional System Description

The description of a collection of objects that provide a function

Process Water Return, Wet Gas, Instrument Air

 

 

 

T0080

Functional System Number

The identification code for a collection of objects that provide a function

PWR, WG, BA, IA

 

 

 

T0081

Hazardous Area Flag

Is the artefact located in a hazardous area?

Y/N

 

 

 

T0082

Heat Trace Medium

Heat trace medium

Oil,Steam,Electrical

 

 

 

T0083

Heat Trace Medium Temperature

Temperature of medium used for heat tracing

122, C

 

 

 

T0084

Heat Trace Requirement

Boolean indication of heat supplied through a wire (typically on a pipe)

Y/N

 

 

 

T0085

Heat Treatment Requirement

Heat treatment requirement for an artifact, if any

HT not required, HT required, HT per T-123

 

 

 

T0086

Hold Date

Date a hold applied to an artefact or drawing

23 Jun 2014

 

 

 

T0087

Hold Description

Field describing reason for the hold

Hold for vendor data

 

 

 

T0088

Hold Release Date

The date on which a hold was released

17 July 2012

 

 

 

T0089

Hold Status Timestamp

The date and time when the status of a hold is changed

27 July 2012 at 12:30

 

 

 

T0090

Hold Status Value

The status of a hold applied to an object

on Hold , Held, H, NH

 

 

 

T0091

Electrical Hook Up Drawing Number

Drawing showing electrical connections including the location of the connections, connections types, sizes etc

ED-123A

 

TIP0001

RDS2221088

T0092

HeatTrace Installation Detail Drawing Number

A drawing showing details of a Heat Tracing Installation

HT-123A

 

TIP0001

RDS2221088

T0093

Pneumatic Hook Up Drawing Number

Drawing showing pneumatic connections including the location of the connections, connections types, sizes etc

PN-123A

 

TIP0001

RDS2221088

T0094

Process Hook Up Drawing Number

Drawing showing connections to the process system including the location of the connections, connections types, sizes etc

PH-123A

 

TIP0001

RDS2221088

T0096

Pipe Support Detail Drawing

Drawing showing pipe support detail , may be either a typical installation or an installation for an engineered support

PipeS-123A

 

TIP0001

RDS2221088

T0097

Hydro Test Pressure

The pressure applied to water in an object or connected objects to test for leaks or other failure

200, PSI

 

 

 

T0098

Output Signal Type (Analog/Digital)

The type of output signal (digital or analog) that a device has

A, D

 

 

 

T0099

Planned Installation Date

UTC Date/Time Installation of artefact is planned to occur

3-12-2014

 

 

 

T0100

Installation Detail

An identification code for a document which contains information to assist with installation of an item

32-GX-12345

 

TIP0001

RDS2221088

T0102

Instrument Air Supply Pressure

Pressure of air to be supplied to instruments to operate the instrument

100 , PSIG

 

 

 

T0103

Instrument Function

Alphabetical character which defines function or process which it is going to perform

Summing, Analyzing etc

 

 

 

T0104

Instrument Index Flag

Indicates whether Artefact appears in Instrument index Report

Y/N

 

 

 

T0105

Instrument Location

A generic classification of instrument location

Field, DCS

 

 

 

T0106

Instrument Sub Type

Detailed classification of an instrument

Flow Transmitter

 

 

 

T0107

Instrument Type

High level classification of an instrument

Transmitter

 

 

 

T0108

Instrument Type Modifier

Specialization indication for an instrument type. See ISA codes per ANSI/ISA 5.1-1984 (R1992)

L, T, P

 

 

 

T0109

Insulated

Boolean indication of heat insulation associated with an artifact (e.g. pipe insulation)

Y/N,Unknown

 

 

 

T0110

Insulation Density

Density of the insulation

0.0, kg/m^3

 

 

 

T0111

Insulation Purpose

The reason for insulation on a pipeline, tank, etc.

Heat Conservation, Personal Protection

 

 

 

T0112

Insulation Spec

Identification code for insulation specification

N-NT

 

TIP0001

RDS2221088

T0113

Insulation Thickness

Width of the insulation from internal surface to external surface

3.5, mm

 

 

 

T0114

IO Card Location

IO card location where the IO Instrument is wired to

Main Room, IO room

 

 

 

T0115

Isometric Drawing Number

Identification code for an isometric drawing where an object such as a specific valve or instrument is shown

ISO-123

 

TIP0001

RDS2221088

T0117

Length Tan To Tan

A straight linear distance which is the total length of the cylindrical section/part of a cylindrical vessel (ie. including the cylindrical sections of the vessel heads)

420, mm

 

 

 

T0118

Line Display Label

A label on the drawing for a line that the component forms part of. It typically consists of the Tag Identification Code concatenated with other properties

HC-3"-GW0-1234

 

 

 

T0120

Line Sizing Calculation Number

An identifier for the Calculation used as the basis for line sizing - may be be a physical document or some other reference

1-ABC-123

 

TIP0001

RDS2221088

T0122

Cartesian Coordinates

Position of a PossibleIndividual, expressed in Cartesian coordinates of a given coordinate system.

123.4, 56.7, 8.90, My Plant Coordinate System

 

 

 

T0123

Logic Drawing

An alphanumeric identifier for the graphical representation of the logic design or a portion thereof; displays the existence of functional elements and the paths by which they interact with one another

ILD-123A

 

 

 

T0124

Loop Drawing Number

The identification code of a loop drawing

L-1234

 

TIP0001

RDS2221088

T0125

Loop Drawing Title

The descriptive name of a loop drawing

Analyzer loop 123

 

TIP0001

RDS2221088

T0126

Loop ID

An alphanumeric identification code for instrument control loop

120P-480

 

TIP0001

RDS2221092

T0127

Loop Process Function

An alphanumeric code denoting the primary process function of a control loop as defined in the ISA standard

L, T, P

 

 

 

T0128

Loop Sequence Number

Numeric part of an instrument loop tag

001

 

 

 

T0129

Loop Suffix

Suffix for an instrument loop tag

A, B

 

 

 

T0130

Manufacturer

The name of the company credited with manufacturing an artifact

Acme Co

 

 

 

T0131

Mass Flow Design Capacity

Estimated rate of mass movement at maximum intended continuous flow

2000, t/h

 

 

 

T0132

Material of Construction Class

A code that represents a chemical composition of a material

M6

 

 

 

T0133

Material of Construction Class Shell

Material of construction class for a shell

M5

 

 

 

T0134

Material Requisition Line Item Number

Identification number for a particular item in a material requisition

1, 2, 3

 

 

 

T0135

Material Requisition Number

Identification code of a form submitted to request supply of artifacts

P-1234

 

TIP0001

RDS2221088

T0136

Maximum Allowable Working Pressure

The maximum pressure that an artifact is designed to withstand

500 , 110, PSI , kPa

 

 

 

T0137

MCC Cubicle Tag

Tag number of the motor control center cubicle providing power

MCC-123-001

 

TIP0001

RDS2221091

T0138

Measured Variable Code

A letter indicating a measured or initiating variable. It is the first letter of the ISA instrumentation code.

P, F, T

 

 

 

T0139

Model Number

The manufacturer's identification code for a type of artifact

NW-45689A

 

TIP0001

RDS2229916

T0140

Module Number

The AlphaNumeric Code identifying the module that a component is part of

D12, Heating Unit 1 etc

 

TIP0001

RDS2221095

T0141

Name Plate Power

Manufacturer supplied power rating

2.5, Hp

 

 

 

T0142

Nominal Diameter

A diameter which is an expected (theoretical/as designed) diameter

3"

 

 

 

T0143

Nominal Pressure Rating

Classes of standard pressure ratings, i.e. the maximum allowable non shock working gage pressure at a given temperature and a specific material.

300#,600# etc

 

 

 

T0144

Normal Ambient Operating Temperature

The ambient temperature at which a device is expected to operate without protective measures

20, C

 

 

 

T0145

Normal Liquid Level

The level of fluid a device contains under nominal operating conditions

120, mm

 

 

 

T0146

Normal Operating Volume

The volumetric quantity of fluid a device contains under nominal operating conditions

30, m^3

 

 

 

T0147

Nozzle Type

Description of nozzle type derived from classification

Nozzle Type

 

 

 

T0148

Number of Conductors

The number of conductors in a cable

3,10

 

 

 

T0149

Number of Tubes

A number which is the number of tubes in an assembly such as a tube bundle

214

 

 

 

T0150

Object Name

 

 

 

 

 

Previous Tag Name

A previous Tag code which typically happens after plant acquisition where new owner imposes their tagging scheme or tag name change during design.

OEX-V100

 

 

 

T0152

Opening Action

A characterization of the rate of opening for a valve

Linear, Quick, Equal Percentage

 

 

 

T0153

Fluid Name

Descriptive Name of Fluid Contained in Pipe, Valve or Equipment

Water, Chlorinated hydrocarbons

 

 

 

T0154

Fluid Code

An identification code for an operating fluid

W, APU

 

 

 

T0155

Operating Mode

Operational duty rating (typically continuous, intermittent, etc.)

intermittent

 

 

 

T0156

Operating Pressure

The pressure at which a process is designed to operate

215 , 51, PSI,kPa

 

 

 

T0157

Operating Temperature

The temperature at which a process is designed to operate

200, C

 

 

 

T0158

Operational Weight

Estimated or calculated weight of an artifact including the material it normally contains

2450, kg

 

 

 

T0159

Valve Operator Type

The mechanism type of the actuator for a valve

Motor, Handwheel, Chain

 

 

 

T0160

Option Code

A code that represents an option in a specification for artifacts such as valves and speciality items

A,B,C

 

 

 

T0161

Orifice Bore Diameter

The diameter of an orifice plate bore

2, cm

 

 

 

T0162

Orifice Vent Port Diameter

The diameter of an orifice plate ventilation port

1, mm

 

 

 

T0163

Overflow Liquid Level

The level of fluid in a device causing an overflow condition

575, mm

 

 

 

T0164

P&ID App Internal Identifier

An internal identifier used in a P&ID application, typically as a database primary key

D42F98C9A2

 

 

 

T0165

P&ID Drawing Number

Identification number for diagram which shows the interconnection of process equipment and the instrumentation used to control the process

123-F-0012

 

TIP0001

RDS2221088

T0166

P&ID Drawing Title

Title describing the P&ID purpose or content of P&ID

Instrument Air system

 

 

 

T0167

P&ID Symbol Name

P&ID CAD system symbol name (e.g. Intergraph AABBCC code)

6QTR13

 

 

 

T0168

Plant Unit Description

A description of a specific plant unit within a plant breakdown structure

Primary water treatment

 

 

 

T0169

Parent Equipment Number

Identification code of Primary Equipment from the viewpoint of some related equipment

P-101

 

 

 

T0170

Part of

Same as Driver Tag Name

58-M-001

 

 

 

T0171

PFD No

Drawing number of process flow diagram on which equipment appears

123-F-0012

 

TIP0001

RDS2221088

T0172

Pipe End Preparation

Preparation of pipe ends prior to assembly

BW,SW,Plain, Threaded

 

 

 

T0173

Line Tag

A unique (within a context such as a plant) identifcation code for the line that a segment is a part of

6"-ST-C2A-100

 

TIP0001

RDS2221093

T0174

Pipe Run Type

Optional identifier to differentiate between major and minor process lines on a P&ID; typically they are drawn with differing linestyles

Primary, Secondary, Major,Minor, Vent, Drain, Utility etc

 

 

 

T0175

Pipe Run Type

Optional identifier to differentiate between major and minor process lines on a P&ID; typically they are drawn with differing linestyles

Primary, Secondary, Major,Minor, Vent, Drain, Utility etc

 

 

 

T0176

Piping Component Type

Class of piping component

PIPE TEE

 

 

 

T0177

Piping Material Class

Classification of material used for a pipe

API 5L Grade B, HDPE

 

 

 

T0178

Piping Material Class

Classification of material used for a pipe

API 5L Grade B, HDPE

 

 

 

T0180

Piping Nominal Diameter

A diameter for process piping which is an expected (theoretical/as designed) diameter

NPS 6

 

 

 

T0181

Plant

An identification code for a plant

P00001

 

TIP0001

RDS2221095

T0184

Plant Unit

Identification code of a specific plant unit within a plant breakdown structure

1, 2

 

TIP0001

RDS2221095

T0186

Power Connection Required

Indicates whether an object requires a connection for electrical power

Y, N

 

TIP3100

 

T0187

Power Design Load

Absorbed power at design load

200, hp

 

 

 

T0188

Power Drive Type

Type of driver

hydraulic

 

 

 

T0190

Pressure Drop

Differential pressure decrease across an artifact such as a pipe length, tube bundle, valve, etc.

15 , kgf/cm^2

 

TIP6600

 

T0191

Prime Function

A letter indicating a measured or initiating variable. It is the first letter of the ISA instrumentation code.

P, F, T

 

 

 

T0192

Process Alternate Design Max Pressure

A maximum design pressure based on an alternate case of the process stream typically derived from the process simulation

17.6, kgf/cm^2

 

 

 

T0195

Process Alternate Design Min Temperature

A minimum temperature based on an alternate case of the process stream typically derived from the process simulation

0, C

 

 

 

T0196

Process Design Max Pressure

The maximum pressure based on all cases of the process stream plus a safety factor

26.9, kgf/cm^2

 

 

 

T0197

Process Design Min Pressure

The minimum pressure based on all cases of the process stream plus a safety factor

2.3, kgf/cm^2

 

 

 

T0198

Process Design Max Temperature

The maximum temperature based on all cases of the process stream plus a safety factor

105, C

 

 

 

T0199

Process Design Min Temperature

The minimum termperature based on all cases of the process stream

-10, C

 

 

 

T0200

Is Corrosive

A compound that has the power to corrode or eat into a substance

Corrosive

 

 

 

T0201

Is Erosive

A compound that has the power to erode or eat in to a substance

True, False, Unknown

 

 

 

T0231

Loop Function

Alphanumeric code denoting the function of a control loop such as control, alarm, indication

Alarm, Control

 

 

 

T0232

Material

Classification of matter used in composition of an artifact Same as Material Of Construction Class

M6

 

 

 

T0233

Material Code

Identification code of material class

STAINLESS STEEL, ASTM A 312/A 312M - TP316L

 

 

 

T0248

Is Toxic

A compound that is dangerous to living organisms

True, False, Unknown

 

 

 

T0249

Process Unit

Identification code of a specific process unit within a plant breakdown structure

1, 1A

 

TIP0001

RDS2221095

T0250

Procurement Package Description

A description for a collection of documents and data to support the procurement of goods and services

Supply of generator circuit breakers

 

 

 

T0251

Procurement Package Number

An identification code for a collection of documents and data to support the procurement of goods and services

P-12345

 

TIP0001

RDS2221088

T0252

Project Description

A description for a project

Capacity expansion for unit 1

 

 

 

T0253

Project Number

An identification code for a project

P123456

 

TIP0001

RDS2229905

T0256

Purchase Order Line Item Number

Identification code for a particular item in a purchase order

1, 2, 3

 

 

 

T0257

Purchase Order Number

Identification code for a purchase order

PO_123456

 

TIP0001

RDS2221088

T0258

Quality Class

A classification indicating quality requirements

1, 2, 3, A, B

 

 

 

T0259

Purchased Quantity

The amount of a commodity to be purchased on a purchase order line. The quantity can be measured as a volume, weight, length, each, etc.

10, Cubic Metre, Tonnes, Feet, Each, Volume, Weight, Length, Dimensionless

 

 

 

T0260

Rated Capacity

The value of a specified type of capacity that an artifact is rated for

0.8, m^3/day, Volume, Mass Flow Rate, Heat Flow Rate

 

 

 

T0261

Rated Discharge Pressure

A discharge pressure at rated capacity

23, kgf/cm^2

 

 

 

T0262

Rated Duty

An unspecified type of duty that an artifact has as is its normal rating

17, kW, m3/hr, kg/sec, Mass Flow Rate, Heat Flow Rate, Volume Flow Rate

 

 

 

T0263

Rated Voltage

Voltage item is designed for at rated load

550, v

 

 

 

T0264

Reason for Issue

The reason that a document is issued

Bid, Construction, Use, Supersede

 

 

 

T0265

Regulatory Requirement

This is the document paper or electronic that represents the regulatory requirement e.g. ASME xxx , BS xxx or DIN xxx

ASME VIII

 

 

 

T0267

Remarks

General comments regarding equipment

need supplier

 

 

 

T0270

Requisition Responsibility

The entity responsible for requisitioning an item

Vendor, Contractor, Owner

 

 

 

T0271

Revision Code

A code used to indicate the revision status of a document

A, 0, 1

 

 

 

T0272

Revision Date

The date that a document was revised

Jan 1, 2013

 

 

 

T0273

RPM

Rotational speed of driven item

3600, rpm,rps

 

 

 

T0274

Equipment Protection Level

A category indicating the level of protection offered by the equipment, i.e. the ability to withstand and/or be suited for use in particular hazardous conditions

I, II, III

 

 

 

T0275

Safety System Classification

A classification of plant artifacts that are required to fulfill some safety function. This can be used to determine reliability requirements.

1, 2, 3

 

 

 

T0277

Safety Instrumented System

A system made up of one or more safety instrumented functions designed to prevent or mitigate hazardous events

SS-001

 

 

 

T0278

Safety Integrity Level

Safety Integrity Level (SIL) is defined as a relative level of risk-reduction provided by a safety function, or to specify a target level of risk reduction. In simple terms, SIL is a measurement of performance required for a Safety Instrumented Function (SIF).

1, 2, 3, 4

 

 

 

T0280

Schedule Or Thickness

A general industry standard classification of the wall thickness of a pipe

Sch 40

 

 

 

T0281

Schematic Drawing (Electric)

Identification code of a wiring drawing

EWD 12345l

 

TIP0001

RDS2221088

T0282

Seal Piping Plan

A schematic diagram showing the connection of piping to a pressurized seal

Seal Plan 11

 

TIP0001

RDS2221088

T0283

Seismic Class

A classification of seismic design requirements

I, II

 

 

 

T0287

Service Description

A description of the purpose of the item

Potable Water

 

 

 

T0288

Set Pressure

A pressure at which an object is activated

12.3, kgf/cm^2

 

 

 

T0289

Shell Nominal Diameter

The nominal diameter of the shell of an equipment such as a heat exchanger

93, mm

 

 

 

T0291

Output Signal Protocol

Classification of method of transmission of information from a device

4-20 mA, 24 VDC, Volt Free contacts, Fieldbus, HART

 

 

 

T0292

Single Line Diagram

Electrical one line diagram on which equipment appears

035-S-011

 

TIP0001

RDS2221088

T0293

Site Assembly Required

Indicates that work is required on site to create a complete artifact (usually equipment)

Y, N

 

TIP3100

 

T0294

Skid Number

An identification code for a skid and its mounted objects

S12345

 

TIP0001

RDS2221095

T0295

Instrument or Electrical Equipment Mounting Location

The location of an instrument or electrical equipment, such as on a skid, panel, or instrument rack

Rack, Panel, Skid, Field

 

 

 

T0296

Slope

Indication of angle relative to a horizontal plane, always a positive value; sometimes stated as a ratio like 5-12

12, deg

 

 

 

T0298

Soft Tag Flag

A flag indicating that an instrument is a software signal

Y/N

 

 

 

T0299

Source of Data

Latest and most reliable source of data for an artifact

Preliminary Estimate, Catalog Data, Vendor Reviewed

 

 

 

T0300

Signal Line Type

Graphical Representation Of Relationship Between Instruments in a Loop

Pneumatic, Hydraulic, Electrical

 

 

 

T0302

Spool Display Label

A label on the drawing for a spool that the component forms part of. It typically consists of the line identification code concatenated with other properties

3"-HC-Spool1

 

 

 

T0303

Startup/Commissioning System

A collection of objects that will be commissioned together

ABC

 

TIP0001

RDS2229985

T0304

Document Number

Document Identification Code that is the standard for the project

DC-233-WQ

 

TIP0001

RDS2221088

T0305

Standard Locator Code

Unique Identification Code Assigned to a document typically by a document management system

DC3412345b

 

 

 

T0307

Steam Out Pressure

Pressure of steam used for cleaning an artifact

32,200 , kgf/cm^2,PSI

 

 

 

T0308

Steam Out Requirements

Requirements for cleaning an artifact using steam

Yes

 

TIP3100

 

T0309

Steam Out Temperature

Temperature of steam used for cleaning an artifact

99, C

 

 

 

T0310

Stock Code

A company specific alphanumeric identifier for a type of object as distinct from tag numbers or purchase orders

D1234-AW3

 

 

 

T0311

Stream No

An identifier (typically a number) assigned to a process stream during design

1, 2

 

TIP0001

RDS2221094

T0312

Stress Analysis Requirements

Category for Stress Calculation (Yes,No,Visual, Simple, Complex, or 1, 2, 3)

No

 

 

 

T0313

Stress Relief Requirement

The requirements for stress relief, typically by heat treatment

none, HT-1234

 

 

 

T0314

Sub Facility Description

A description of a subdivision of a facility

Reactor 21

 

 

 

T0315

Sub Facility Number

An identification code for a subdivision of facility typicaly based on geography rather than function

A, Sed1, R21

 

TIP0001

RDS2221095

T0317

Sub Project Number

Alphanumeric code for lower level element in task structure

A123-A

 

TIP0001

RDS2229905

T0318

Supplied By

Code indicating the type of supplier of an artifact

Owner, Vendor

 

 

 

T0319

Supply Responsibility

The entity responsible for supplying an item

By Owner, Vendor, Contractor

 

 

 

T0320

Switchgear Supplying Power

The equipment used to engage or disengage power (mechanical or electrical) to the specified device

S-A025-001

 

 

 

T0321

System Block Diagram

A high-level system schematic drawing showing the relationship between the main functions or components of a system

D-1234

 

TIP0001

RDS2221088

T0323

Tag Prefix

A text string that is part of a tag, often used to denote equipment type

HX

 

 

 

T0324

Tag Sequence Number

A sequence number that forms part of the tag

 

 

 

 

T0325

Tag Suffix

Postpended segment of a tag

A, B

 

 

 

T0326

TEMA Designation

To classifiy Heat Exchangers TEMA has designated a system of notations that correspond to each major type of front head, shell style and rear head. The first letter identifies the front head, the second letter identifies the shell type and the third letter identifies the rear head type

AEU

 

 

 

T0327

Terminal Block From Wire End

Connection between one wire end and the Terminal Block

Block 6-1

 

 

 

T0328

Terminal Block To Wire End

Connection between one wire end and the Terminal Block

P8

 

 

 

T0329

Terminal Point From Wire End

Connection of the from Wire End to Specific Terminal Point on a Terminal Block

Block 6-1

 

 

 

T0331

Test Package

A grouping of physical items for commissioning testing. Examples include hydro testing of piping packages and various other discipline test activities

T123

 

TIP0001

RDS2221088

T0332

Thermal Expansion Coefficient

A numeric factor that gives the relationship between length and temperature

0.001, mm/deg C

 

 

 

T0333

Document Title

A phrase that identifies and describes a document

System XYZ Functional Description

 

 

 

T0334

To From Tags Description

A description of the main source and destination tags of a line

From U-01005 To T-123

 

 

 

T0335

Train Number

An identifier for parallel process facilities in a plant

A, B, 10, 20

 

TIP0001

RDS2221095

T0336

Trim Spec

ID of document detailing the internal components of a valve

 

 

 

 

T0337

Tube Length

The length of a tube in a heating transfer device

2.0, m

 

 

 

T0338

Unit Process No

Subunit within a Process Area such as a Cracking Furnace within a Cracking Area or distillation unit in the distillation area

1, 2A , F1

 

TIP0001

RDS2221095

T0339

Updated By

Name of the person who last updated information

JDOE

 

 

 

T0340

Vacuum Design Requirements

Design requirement for vacuum conditions

Full Vacuum

 

 

 

T0341

Vacuum Pressure

Pressure expressed in absolute values - the pressure that would occur at absolute vacuum

1.2,2, psia,kPa

 

TIP6600

 

T0342

Valve Code

Identification code of a specific valve type

ZDR 6 D

 

 

 

T0344

Valve Type

Generic classification of a valve

GATE, CHECK

 

 

 

T0345

Vendor Drawing Number

Alphanumeric Code used to identify the vendors drawing

FI 1234A1

 

TIP0001

RDS2221088

T0346

Vendor Tag

Identification code of an artifact set by the vendor

T-123

 

TIP0001

RDS2221089

T0347

Viscosity Test Method

The method used to test the viscosity of a fluid

ASTM D7042

 

 

 

T0348

Volume Flow Design Capacity

Estimated rate of fluid movement at maximum intended continuous flow

42, m^3/hr

 

 

 

T0349

Volume Rating

The maximum volume of fluid that a container can hold

62, m^3

 

 

 

T0350

Wall Thickness

Perpendicular dimension through a artifact from the inner surface to the outer surface

6,0.125, mm,incg

 

 

 

T0351

Wire Color

The color of the insulation of an electrical conductor

Red, Green

 

 

 

T0352

Wire Tag

 

 

 

TIP0001

RDS2229987

T0353

Wire Tag From End

Identifier Of Nominal Source of a wired connection

Switchboard S1-Teminal 2

 

 

 

T0354

Wire Tag To End

Identifier Of Nominal Target of a wired connection

 

 

 

 

T0355

Wiring Diagram Number

A representation of an electrical circuit showing the components of the circuit and the connections between the devices

1-XYZ-W001

 

TIP0001

RDS2221088

T0356

Wiring Required

Indicates whether an object requires a wiring connection

Y, N

 

TIP3100

 

T0357

X Coordinate

 

 

 

 

 

T0358

Y Coordinate

 

 

 

 

 

T0359

Z Coordinate

 

 

 

 

 

T0360

Location Class

A code describing the type of location of a commodity

Above ground, Below ground, In Rack

 

 

 

T0362

From Tags Description

A description of the main source tags of a line

 

 

 

 

T0363

To Tags Description

A description of the main destination tags of a line

 

 

 

 

T0364

Approval Status

Classification of approval status separate from issue status

Approved For Construction, Approved for Purchase, Approved for Design

 

 

 

T0365

Approved for Procurement

 

N

 

 

 

T0366

Aproved for Construction

 

 

 

 

 

T0367

Arrangement Drawing Number

Identification for the drawing on which the object locations are identified; such as a 2D plan view or elevation

CW-OI-A-123

 

TIP0001

RDS2221088

T0370

Supplier Catalog Name

Identifier of a catalog generally containing parametric definitions of components such as valves, pipe fittings, etc.

Black Box Catalog

 

TIP0001

RDS2221088

T0373

Centerline Length

Length of an artifact (typically estimated, measured or calculated) along the center line

8.4, m

 

 

 

T0374

Code Category Hazard Class

Code category hazard class

Category M

 

 

 

T0375

Construction Work Package Number

An identification code for a collection of project objects and associated construction activities

WP-A035-001

 

TIP0001

RDS2221088

T0376

Requested Delivery Date

Date that delivery of artifact is required on site

20 July 2013

 

 

 

T0377

Delivery Date

Date that artifact was received on site

20 June 2013

 

 

 

T0378

Depth

Single value typically representing a distance to the bottom of a fluid from the surface of the fluid

1.2,8, m,ft

 

 

 

T0381

Design Capacity

The value of a specified type of capacity that an artifact is designed for

10.2, liter/sec, Volume, Mass Flow Rate, Heat Flow Rate

 

 

 

T0382

Design Code

Published specification controlling construction materials and/or methods

API621

 

 

 

T0383

Design Temperature Line

Design temperature of the line

0, C

 

 

 

T0384

Delivery Destination Name

A place name where products are to be delivered to

Plant A laydown area B, Fab shop X

 

 

 

T0385

Differential Pressure Tap Type

The location or configuration of taps around an orifice plate for connection to a differential pressure instrument

Flanged, Corner, Radius

 

 

 

T0386

Shipping Dimension Description

A text description consisting of the length, width, and height dimensions of the envelope of an artefact as prepared for shipping

10'2"L x 8'6"W x 2.0"H

 

 

 

T0390

Discipline Specialty Group Name

The name of a group with specialty knowledge of a subject

Machine Design, Bulk Material Handling, Piping

 

 

 

T0409

Equipment Sizing Calculation Number

An identifier for the Calculation used as the basis for equipment sizing - may be be a physical document or some other reference

V-102 Sizing Calculation Sheet

 

TIP0001

RDS2221088

T0413

Fluid Name (Line)

Descriptive name of fluid contained in a line

Water, Chlorinated hydrocarbons

 

TIP0001

RDS2221094

T0414

Fluid State

The phase of a fluid material, such as liquid, gaseous, solid powder, mixtures, etc.

Liquid, Gas, Liquid/Gas

 

 

 

T0416

Functional Group Code

A code identifying a number of things having a special activity, purpose, or task, that are classed together, is known, addressed, or referred to.

100, 200, 300

 

 

 

T0417

Functional Group Name

A word or set of words by which a number of things having a special activity, purpose, or task, that are classed together, is known, addressed, or referred to.

Project Mgmt, Engineering, Procurement

 

 

 

T0421

Geometric Area

The area of a surface (for example A= L x W)

10, sq m

 

 

 

T0422

Hazardous Area Classification

A classification corresponding to a physical area which is deemed to contain a hazard of some type

Y, N, 1, 2, Class II, Div. 2

 

 

 

T0423

Installation Completed Date

UTC Date/Time Installation of artefact is complete

5-23-2010

 

 

 

T0424

Installed By

The entity responsible for installing an item

Vendor, Contractor, Owner

 

 

 

T0427

Instrument Detail

An identification code for a detail within a document which contains additional information related to an instrument

A

 

TIP0001

RDS2221088

T0428

Insulation Temperature

Temperature at the outside surface of the insulation

121, C

 

 

 

T0430

Is Inline

A flag showing whether a component is inline with piping

yes, no

 

 

 

T0431

Issued Date

The date of the latest issue of a document

1/2/2013

 

 

 

T0432

Insulation Material

Material of construction of insulation

Fiberglass, Calcium silicate

 

 

 

T0433

Document Sub Type

A subclassification of a document

Bill of Material, Calculation, Datasheet

 

 

 

T0435

Set Point

A value of a property for triggering an action

120, 167, 210, psig, deg C, mm, Pressure, Temperature, Length

 

 

 

T0438

Safety System Classification

A classification of plant artifacts that are required to fulfill some safety function. This can be used to determine reliability requirements.

1, 2, 3

 

 

 

T0439

Max Suction Pressure

The lowest pressure that can be present at the suction inlet

100, kPa

 

 

 

T0440

Impeller Diameter

Diameter of pump Impeller

1000, mm

 

 

 

T0441

Location Drawing

Drawing ID showing locations of artifacts

1XYZ-28

 

TIP0001

RDS2221088

T0447

MeasuredLength

The length of an artifact as actually measured

,

 

 

 

T0448

Child Equipment Number

Identification code of Secondary Equipment from the viewpoint of the Primary or Parent equipment

M-123

 

 

 

T0449

Supplier Name

The name of the supplier of an artifact

Acme Pumps

 

TIP0001

RDS2229785

T0450

CasingDiameter

The outside diameter of the enclosure for an equipment

100, mm

 

 

 

T0452

Process Alternate Design Max Temperature

A maximum temperature based on an alternate case of the process stream typically derived from the process simulation

86, degC

 

 

 

T0453

Process Alternate Design Min Pressure

A minimum design pressure based on an alternate case of the process stream typically derived from the process simulation

1, kgf/cm^2

 

 

 

T0455

Safety Instrumented Function

The specific control functions performed by an Safety Instrumented System (SIS) to achieve a given Safety Integrity Level (SIL)

SIF-001

 

 

 

T0456

Terminal Point To Wire End

Connection of the from Wire End to Specific Terminal Point on a Terminal Block

Block 6-2

 

 

 

T0457

Thermowell Bore Diameter

An inside diameter of thermowell at temperature element connection point

7, mm

 

 

 

T0458

Thermowell Outside Diameter at Support

The outside diameter of a thermowell stem adjacent to the process connection

19, mm

 

 

 

T0459

Thermowell Outside Diameter at Tip

Outside diameter at the tip on a thermowell

12.5, mm

 

 

 

T0460

Thermowell Insertion Length

The length from the thermowell sealing face to the tip

50, mm

 

 

 

T0461

Thermowell Tip Thickness

Thickness of the thermowell at its tip

2.25, mm

 

 

 

T0462

Thermowell Stem Type

The type of thermowell stem (the part that is inserted into the process piping or equipment) such as tapered, straight, or stepped.

tapered, straight, stepped

 

 

 

T0463

Thermowell Process Connection Type

The mounting style of a thermowell based on the application requirement, such as threaded, welded, or flanged

Threaded, Socket Weld, Flanged

 

 

 

T0464

Thermocouple Type

A code designating the two types of material that make up the thermocouple

Type J

 

 

 

T0466

Serial Number

A unique identification code assigned by the manufacturer to each manufactured item

942518

 

TIP0001

RDS2221101

T0467

Process Instrument Mounting Bracket Type

The type of instrument mounting bracket that is a support structure for mounting an instrument

B1, B2, Flanged

 

 

 

T0468

Ingress Protection Rating

The ingress protection rating of a housing, for example of an instrument or equipment

IP44, IP67, IP69K

 

 

 

T0469

Thermowell Process Connection Size

The size of the thermowell connection to the process

3/4 in NPT

 

 

 

T0470

Class Pattern: Hydro Test Pressure

A ClassOfInanimatePhysicalObject to be tested participates in a pressure testing ClassOfActivity, a test fluid participates in that same ClassOfActivity, and that test fluid has a test pressure with a value and a unit of measure

10, bar

 

 

 

T0471

Transient Protection Required

Does the device need protection from induced electrical transient overvoltages?

Yes, No

 

TIP3100

 

T0472

Integral Indicator Type

The type of physical indicator on an instrument for presenting information/measurement data locally

None, LCD Display, Analog Indicator

 

 

 

T0473

Tag Plate Type

The type of tag plate manufactured per requirement of the end user

Wire-on Tag with SS 304 Material

 

 

 

T0474

Enclosure Material

A material of a housing or enclosure that is the external part of an instrument or equipment

Aluminum, SST

 

 

 

T0477

Gasket or O-Ring Material

The type of material that a seal such as a gasket or o-ring is made from

PTFE, Neoprene, Enclosure gasket, shaft o-ring

 

 

 

T0478

Conduit Connection Type

The size and type of conduit fitting provided for connections on an instrument or equipment

3/4 NPT-F, 1/2 NPT-F

 

 

 

T0479

Detecting Element Type

The type of artefact that senses and converts the input variable into a signal.

Diaphragm, Thermistor, Float

 

 

 

T0480

Accuracy

Degree of closeness of measurements of a quantity to that quantity's actual (true) value

0.025, 1.0, percent of span, degree Celcius

 

 

 

T0481

Spatial Location

A position in the plant coordinate system

55.26, 1224.1, 5634.0

 

 

 

T0482

Plant Coordinate System Definition

Information defining a plant coordinate system such as dimension, type, and units of measure

Cartesian, 3D, meters, degrees

 

 

 

T0483

Normal Capacity

The value of a specified type of capacity for an artifact under normal conditions

123, m3/hour, Volume, Mass Flow Rate, Heat Flow Rate

 

 

 

T0484

Suction Pressure Rated

 

12, psig

 

 

 

T0485

Differential Head

The difference in pressure across a device measured in length units of a specified fluid

23, Metre H2O at 4 Degree Celsius

 

TIP6600

 

T0486

NPSHA

The available pressure at the inlet of a device measured in head of a specified liquid

23, Metre H2O at 4 Degree C

 

TIP6600

 

T0487

Process Variation Conditions

A description of the type of Process Variability that may be encountered

Surging may be encountered at low flow

 

 

 

T0488

Starting Conditions

A description of process conditions at equipment startup

Start with Outlet Valve Closed

 

 

 

T0489

Starts Per Day

Number of Starts Equipment is expected to perform per day

4

 

 

 

T0490

Parallel Operations Required

Definition of a requirement for parallel operations

Yes, No, Unknown

 

TIP3100

 

T0491

List Price

A basic published or advertised price for a commodity often subject to discount.

1200, $

 

 

 

T0492

Explosion Certification

IECEX Explosion Proof rating, ATEX Rating

IECEX 02, IECEX 02A, ATEX 95 zone 2

 

 

 

T0493

insulation thickness a

Width of the insulation from internal surface to the external surface

3.5, mm

 

 

 

T0494

PSV Back Pressure

The pressure that exists at the outlet of a pressure relief device as a result of the pressure in the discharge system e.g. flare system, blowdown system etc. It is the sum of the superimposed and built up back pressure.

12, psig, barg

 

TIP6600

 

T0495

Bursting Pressure

A pressure at which a device such as a vessel, pipe, or rupture disk will burst

320, psig

 

 

 

T0496

Cold Set Pressure

The pressure at which the pressure relief valve is adjusted to open on the bench. It includes corrections for back pressure and/or temperature.

123, psig, kPa

 

 

 

T0497

Reseat Pressure

The Pressure at which a safety valve reseals after an opening

100, barg

 

 

 

T0498

Blowdown

The ratio between the set pressure and the reseating pressure of a pressure relief valve, expressed as a percentage of the set pressure

10, %

 

 

 

T0499

Rated Duty Description

A Description of the Duty Cycle e.g. Continuous, Intermittent etc

Continuous

 

 

 

T0500

Hardness

The hardness value of a weld or pipe, as measured using a scale such as Rockwell or Brinell

120, HB

 

 

 

T0501

Isometric Drawing Number

The identification code of an isometric drawing that an artifact is represented on

P-12-123-1

 

TIP0001

RDS2221088

T0502

Isometric Drawing Revision

Code to identify and track the revisions for an isometric drawing

01

 

 

 

T0503

Isometric Drawing Sheet Number

Sheet Number with Isometric Drawing package

1,2,3

 

 

 

T0504

Hand Over Sub System ID

the hand over sub-system unique identification number

 

 

TIP0001

RDS2229985

T0505

NDT requirement

Non destructive testing (yes or no)

Y, N

 

TIP3100

 

T0506

P&ID Revison

The revision of the piping and instrument diagram that an artifact is represented on

A, 0, 1

 

 

 

T0507

Specific Gravity

the specific gravity of the fluid inside the pipe, equipment etc (SG Water)

1.0

 

 

 

T0508

Stress Package

The Name assigned to the package that consists of a grouping of lines that require Stress Analysis. Typically of the form Area-Seq No.

100-001

 

TIP0001

RDS2221088

T0509

Hydro Test Liquid

Type of liquid used for pressure testing the Artefact in question

Water, Air, Nitrogen

 

 

 

T0510

Unit Weight

Standard weight of the component, either as a total weight (per each) or a weight per unit of measure.

10, kg, lbs per foot

 

 

 

T0511

Item Long Description

A detailed description for purchase/stock control. Typically includes design Code, component type and material

90 DEG ELBOW A105N FORGED NPT-F ASME B16.11 CL.3000 GALV Size: .75"; 300 x S-STD Pipe, ASME B36.10M, Bevel End, ASTM A 53 Grade B, Electric Resistance Welded

 

 

 

T0512

Material Standard Code

The Short Code for an organization that defines the material standard for an artefact

ASTM, ASME, API, DIN

 

 

 

T0513

Primer Coating Code

The code used to identify the material and application process to be used for a primer coat

PR-123

 

 

 

T0514

Finish Coating 1 Code

The code used to identify the material and application process to be used for the first finish coat

F-123

 

 

 

T0515

Finish Coating 2 Code

The code used to identify the material and application process to be used for the second finish coat, if any

F2-123

 

 

 

T0516

Purchase Order Revison

Code to identify and track the revisions for a purchase order

A, 1, 2

 

 

 

T0517

Shipment Date

Date/Time the item(s) are dispatched

April 1, 2015

 

 

 

T0518

Shipment Number

The Identification Code for the Shipment that an artifact is part of

S-123

 

TIP0001

RDS2229905

T0519

Voyage Number

A number which is assigned to a round-trip sea voyage intended to transport trade goods along an existing trade route.

V.284

 

TIP0001

RDS2229905

T0520

Pipe Support Size

The Nominal Diameter of the Parent Pipe being supported

8"

 

 

 

T0521

Pipe Support Number

An Identification code for the pipe support. In the case of Engineered Supports may be unique to that support. In the case of standard supports may be just a commodity or model no.

H-001

 

TIP0001

RDS2229904

T0522

Weld Type

The type of weld to be used e.g. Butt Weld , Socket Weld etc

BW

 

 

 

T0523

Weld Size

The Nominal diameter of the pipe where the weld takes place

6"

 

 

 

T0524

Weld Rating

A rating based on thickness or some parameter to indicate weld rating i.e. 1500# for Socket Weld or Sch 160 for Butt Welding

1500# , Sch 160

 

 

 

T0525

Dye Penetrant Inspection Requirements

Dye Penetrant Inspection requirements

10%, inspect all welds at high stress points etc

 

 

 

T0526

Magnetic Particle Inspection Requirement

The percentage of welds required to be inspected with a magnetic particle test

10%, inspect all welds at high stress points etc

 

 

 

T0527

NDT Class

The specification describing the non-destructive testing requirements for an artefact

E243-13, E165M-12

 

 

 

T0528

Weld Spec

welding procedure specification number

W-1234

 

 

 

T0529

Radiographic Inspection Requirements

The percentage of welds required to be inspected with radiographic testing

10%, inspect all welds at high stress points etc

 

 

 

T0530

Dimensional Standard

An industry standard that covers the sizes of piping components

ASME B16.9

 

 

 

T0531

Coating Code

A code reference to a specification defining the materials and application process to be used to paint or coat the outside or inside of the artefact

P-123

 

 

 

T0532

Pipe Support Type

A classification of a support as rigid, spring, snubber, etc.

RIG, SPR, SNB